ENVIRONMENTAL AGING CHAMBERS

Articles

• Mechanical characterization
  17 June 2015, by Administrateur

  MECHANICAL CHARACTERIZATION: Microstructure, hardness of materials, abrasion resistance, etc.
  Mechanx²ical tests are used to determine the behavior of materials and identify their mechanical characteristics. These characterizations are used to ensure that the structure of the material will be tailored to the use of the final part and thus overcome any possible defects or breakages in operation.
  The laboratory’s equipment allows us to determine the following characteristics:
  • Determination (...)

• Characterization of coating strength
  17 June 2015, by Administrateur

  CHARACTERIZATION OF COATING STRENGTH: The characterization of surface coatings
  The Analyses & Surface CRT is equipped with standardized hardware and has developed the skills to meet the increasingly stringent technical and regulatory requirements (higher temperatures, more aggressive environments, vibration, high stress, high pressures, REACH recommendations or standards, etc.). These parameters require evaluation and the qualification of coatings and their refractory life according to (...)

• Corrosion defect analysis
  17 June 2015, by Administrateur

  STUDY OF CORROSION PHENOMENA: Searching for the cause of premature aging or the incompatibility between a material and its environment
  This type of defect can pose a risk to the reliability and strength of the materials. Understanding corrosion phenomena enables manufacturers to control the risks in relation to the relevant technical and economic issues.
  The capacity to implement the aging tests and analyze the corrosion phenomena involved is a specific feature of the Analyses & (...)

• ENVIRONMENTAL AGING CHAMBERS
  10 December 2009, by Administrateur

  Salt spray chambers Operating principle
  A saline solution (prepared with demineralized water and stored in tanks) supplies the enclosure. This solution is sprayed under pressure through a compressed air inlet saturated with water. A deflector enables homogeneous distribution of the spray in the chamber and prevents the direct impact of the sprayed solution on the tested parts.
  Technical characteristics
  Up to Tank capacity (liters): 1000 Height (mm): 900 Width (mm): 1600 Depth (...)

• Photoaging tests
  17 June 2015, by Administrateur

  -AGING RESISTANCE TEST: Assessing the resistance of materials to the solar spectrum (Xenon) and UV rays.
  Photoaging tests (solar spectrum or UV) are designed to simulate accelerated aging due to solar radiation and climate.
  This laboratory test enables manufacturers to decide on the choice of materials according to the environmental conditions of the target markets.
  The type of chambers used manage the materials’ exposure to radiation, control the temperature and humidity and a water (...)

• CYCLED SALT SPRAY TEST
  11 December 2020, by Marion

  Tests and study of corrosion phenomena
  The ANALYZES AND SURFACE laboratory has within the 6NAPSE Group a cycled chamber with neutral salt spray that can meet many standards and CDC.
  The resistance of materials or finished parts to the life cycle is an important criterion in the validation of a design. The choice of metallic materials, treatments or paints is essential in the lifespan of a product and that for many sectors of activity.
  Oxidation phenomena or appearance defects are (...)

• FLUID SUSCEPTIBILITY TEST
  5 January 2021, by Marion

  Fluid susceptibility tests
  For several years, the ANALYSIS ET SURFACE laboratory has been carrying out fluid susceptibility tests according to EUROCAE ED-14G RTCA DO-160 Section 11 (Fluids Susceptibility) or other standards in different sectors of activity (Example: NF ISO 28121, standard VOLVO 1026.8177 or Renault Nissan RNES-B-00090 v2.0 D49 3253
  Our resources allow us to take charge of large resistance of coatings to fluids with our immersion and spray possibilities. The behavior of (...)

• Salt spray tests
  17 June 2015, by Administrateur

  ANALYSES ET SURFACE has COFRAC testing accreditation (accreditation n°1-1720 - scope available on www.cofrac.fr for the performance of neutral salt spray tests (NSS) according to NF EN ISO 9227 standard.
  The durability of a material or a product has always been a central concern of buyers worldwide. Metallic materials have many mechanical advantages which cannot be replaced in many sectors. The main drawback is their sensitivity to oxidation in a corrosive atmosphere which affects the (...)

• Thermal shock / cycle tests
  17 June 2015, by Administrateur

  THERMAL SHOCK OR CYCLE TESTING: Assessing the resistance of materials to climate change.
  Temperature and humidity have an effect on the service life of a material or a product. The choice of suitable materials is paramount, and depends on the environmental conditions in which your products are to be used.
  Conducting cycle or thermal shock tests allows us to qualify or control the change in parts under conditions tailored to your specifications or according to existing standards.
  At the (...)